Alan Cox [Fri, 17 Aug 2018 12:17:33 +0000 (13:17 +0100)]
z80: build raw2mgt for Z80 kernel builds
Alan Cox [Fri, 17 Aug 2018 12:17:15 +0000 (13:17 +0100)]
tools: add a raw2mgt too for SAM kernel building
Alan Cox [Fri, 17 Aug 2018 12:09:47 +0000 (13:09 +0100)]
setup: we need the ROM off
Alan Cox [Fri, 17 Aug 2018 12:08:32 +0000 (13:08 +0100)]
sam: correct the boot.s code
At this point we seem to be able to load our image. Not yet tried debugging
what happens after bootstrap loads.
Alan Cox [Fri, 17 Aug 2018 09:44:49 +0000 (10:44 +0100)]
tty: improve behaviour of O_NDELAY
We want to bale out on a polled output port on a reschedule not just sit
assuming the bits will go out shortly
Alan Cox [Fri, 17 Aug 2018 00:35:34 +0000 (01:35 +0100)]
Merge branch 'master' of https://github.com/EtchedPixels/FUZIX
Tormod Volden [Tue, 14 Aug 2018 19:27:24 +0000 (21:27 +0200)]
dragon-nx32: Use the tty_close wrapper to close DriveWire channel properly
Fixes issues when disconnecting login over DriveWire (dwgetty).
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Tue, 14 Aug 2018 19:27:23 +0000 (21:27 +0200)]
dragon-nx32: Correct DriveWire minor offset
Forgot to bump this when adding crt9128 console tty.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
EtchedPixels [Tue, 14 Aug 2018 10:31:50 +0000 (11:31 +0100)]
Merge pull request #653 from beretta42/coco2cart
coco2cart: bug: sdc driver still not returning no of bytes read/writen
Brett Gordon [Tue, 14 Aug 2018 02:07:14 +0000 (22:07 -0400)]
coco2cart: bug: sdc driver still not returning no of bytes read/writen
With this fix it boots again on the CoCo2 w/ SDC
Alan Cox [Mon, 13 Aug 2018 12:53:07 +0000 (13:53 +0100)]
sam: add IDE definitions
Alan Cox [Mon, 13 Aug 2018 12:52:37 +0000 (13:52 +0100)]
sam: more work on fork support for 32/32
Tormod Volden [Sat, 11 Aug 2018 09:32:39 +0000 (11:32 +0200)]
dragon-nx32: Ship custom inittab and rc
inittab:
- do not run sysinit boot shell
- run getty on ttys 1-4
- add commented out dwgetty entry
rc:
- try setting time from DriveWire before resorting to settime
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Sat, 11 Aug 2018 09:18:37 +0000 (11:18 +0200)]
dragon-nx32: Only init IDE if we have a known IDE cartridge ROM
Same as we do for SCSI controllers.
Avoids the long detection timeout when there is no IDE controller
present.
Since we are not using the cartridge ROM, it would be strictly
possible to use a controller without ROM but we won't support
that for now. The same goes for unknown ROMs, of course.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Sat, 11 Aug 2018 23:32:45 +0000 (01:32 +0200)]
dragon-nx32: Minor updates to README
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Alan Cox [Sun, 12 Aug 2018 23:55:57 +0000 (00:55 +0100)]
Merge branch 'master' of https://github.com/EtchedPixels/FUZIX
Alan Cox [Sun, 12 Aug 2018 23:39:57 +0000 (00:39 +0100)]
genie-eg64: New platform (in test only)
The Video Genie EG64 allows you to take a Video Genie (also known as the
Dick Smith System 80, the TRZ80 and a few other names) with either of the
expansion units and the EG64 fitted up to 96K. It's intended for running CP/M
but it's just about big enough to run Fuzix badly providing you have a swap
device on hard disk.
Another goal of this port is to figure out how to move a lot of TRS80 driver
code into dev/trs80 to share between these two ports, a Genie III port maybe,
and also potentially things like the Lobo-Max, Guepard., SysData III and so on.
Alan Cox [Sun, 12 Aug 2018 23:39:26 +0000 (00:39 +0100)]
tools/binman: Teach it about kernels with the data the top of memory
Alan Cox [Sun, 12 Aug 2018 23:39:07 +0000 (00:39 +0100)]
trs80m1: update documentation
Alan Cox [Sun, 12 Aug 2018 23:38:42 +0000 (00:38 +0100)]
trs80m1: Fix more tty bugs
This lot really needs a restructure instead
Alan Cox [Sun, 12 Aug 2018 23:38:13 +0000 (00:38 +0100)]
trs80m1: add initial test UDG support
Needs emulator work to test properly
Alan Cox [Sun, 12 Aug 2018 23:37:35 +0000 (00:37 +0100)]
trs80m1: make the lower case status C visible
Alan Cox [Sun, 12 Aug 2018 23:37:20 +0000 (00:37 +0100)]
trs80m1: remove obsolete comment
Alan Cox [Sun, 12 Aug 2018 23:36:36 +0000 (00:36 +0100)]
trs80m1: remove bogus asm
Alan Cox [Sun, 12 Aug 2018 23:36:13 +0000 (00:36 +0100)]
trs80m1: Fix bogus comment
Alan Cox [Sun, 12 Aug 2018 23:35:33 +0000 (00:35 +0100)]
tty.h: add new font type
Alan Cox [Sun, 12 Aug 2018 23:35:19 +0000 (00:35 +0100)]
trs80m1: remove drivewire reference
Alan Cox [Sun, 12 Aug 2018 23:33:36 +0000 (00:33 +0100)]
dragon-nx-32: note bug to look at
EtchedPixels [Sat, 11 Aug 2018 17:07:06 +0000 (18:07 +0100)]
Merge pull request #651 from beretta42/coco2cart
some fixes for coco2cart SDC support
Alan Cox [Fri, 10 Aug 2018 23:54:11 +0000 (00:54 +0100)]
trs80m1: only one interface is present
Alan Cox [Fri, 10 Aug 2018 23:52:03 +0000 (00:52 +0100)]
trs80m1: move platform_param into discard
We don't need it after boot and we are going to add some options here soon
Alan Cox [Fri, 10 Aug 2018 23:32:42 +0000 (00:32 +0100)]
z80fixedbank-banked: apply the same SP fix as to the main fixedbank code
Alan Cox [Fri, 10 Aug 2018 23:32:20 +0000 (00:32 +0100)]
devide: save two bytes and a few clocks
Alan Cox [Fri, 10 Aug 2018 23:31:49 +0000 (00:31 +0100)]
sam: update boot logic
Thanks to the various Sam folks who explained how BOOT works
Alan Cox [Fri, 10 Aug 2018 23:31:36 +0000 (00:31 +0100)]
rabbit: I guess we use a different rst
Alan Cox [Fri, 10 Aug 2018 23:29:28 +0000 (00:29 +0100)]
trs80m1: simplify make clean
Alan Cox [Fri, 10 Aug 2018 23:29:00 +0000 (00:29 +0100)]
trs80m1: adjust the istack_switched_sp so it doesn't get scribbled
With this fixed we seem to be back in business and 768 bytes better off
Alan Cox [Fri, 10 Aug 2018 21:27:50 +0000 (22:27 +0100)]
trs80m1: and make the IDE drives visible
Alan Cox [Fri, 10 Aug 2018 21:26:27 +0000 (22:26 +0100)]
trs80m1: turn on the probing
Alan Cox [Fri, 10 Aug 2018 21:25:29 +0000 (22:25 +0100)]
trs80m1: rearrange memory so that we get 768 bytes back
We stick the udata/stack over 4100-42FF, and the istack over the boot area at
4300-43FF
Alan Cox [Fri, 10 Aug 2018 21:24:42 +0000 (22:24 +0100)]
trs80m1: turn IDE on in build
Alan Cox [Fri, 10 Aug 2018 21:23:54 +0000 (22:23 +0100)]
trs80m1: build the IDE layer for this machine
Alan Cox [Fri, 10 Aug 2018 21:22:53 +0000 (22:22 +0100)]
trs80m1: add .module to floppy
Alan Cox [Fri, 10 Aug 2018 21:20:22 +0000 (22:20 +0100)]
trs80m1: add IDE layer helpers
Tormod Volden [Thu, 9 Aug 2018 21:56:11 +0000 (23:56 +0200)]
Add .pkg for dragon-nx32 platform
Tormod Volden [Thu, 9 Aug 2018 21:56:10 +0000 (23:56 +0200)]
build-filesystem-ng: Scan Kernel folder for package files
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Alan Cox [Thu, 9 Aug 2018 18:15:37 +0000 (19:15 +0100)]
rc2014: hopefully correctly turn on the IDE CF
Alan Cox [Wed, 8 Aug 2018 22:16:19 +0000 (23:16 +0100)]
sam: next pass over the code working on stuff
Still lots and lots to sort out
Alan Cox [Wed, 8 Aug 2018 22:15:49 +0000 (23:15 +0100)]
rc2014: init IDE
Alan Cox [Wed, 8 Aug 2018 22:15:27 +0000 (23:15 +0100)]
bank32k: note need to do swap
Brett Gordon [Wed, 8 Aug 2018 13:27:15 +0000 (09:27 -0400)]
coco2cart: adjust sdc return to match 256 byte sectors
Brett Gordon [Wed, 8 Aug 2018 13:18:47 +0000 (09:18 -0400)]
coco2cart: reformat boot fail messages
M6847 VDG chips can't do lowercase.
Alan Cox [Tue, 7 Aug 2018 23:16:32 +0000 (00:16 +0100)]
Makefile: The Amstrad NC100 moved
Alan Cox [Tue, 7 Aug 2018 23:15:49 +0000 (00:15 +0100)]
gmtime: not a needed optimization
Alan Cox [Tue, 7 Aug 2018 23:14:54 +0000 (00:14 +0100)]
z80: Initial documentation on how 32K/32K works
Alan Cox [Tue, 7 Aug 2018 23:13:43 +0000 (00:13 +0100)]
kernel: initial development tree for the Sam Coupe
This is so that the 32K/32K split code can be developed. This memory model is
actually a lot more complex and different to the existing Z80 models we use.
Don't expect anything runnable for quite some time.
Alan Cox [Tue, 7 Aug 2018 23:10:05 +0000 (00:10 +0100)]
z80: fix a nasty bug with the full bank switching model on swapless
The swap case is ok as it always runs on the swap stack. The non swap case
restores the process kernel stack underneath the curent sp. That in itself is
fine as we have interrupts off. However we then called map_kernel which if
the current sp was above the sp of the save would corrupt the stack.
Instead restore sp first so that we push and pop data below the saved stack
content
Alan Cox [Tue, 7 Aug 2018 23:07:46 +0000 (00:07 +0100)]
z80: first sketches of the 32K/32K support
Some of this will also hopefully apply to the 64K/ROM switch and the Cromemco /
NASCOM style models where you have write through to multiple banks but 64K
switching
Alan Cox [Tue, 7 Aug 2018 23:05:58 +0000 (00:05 +0100)]
lowlevel-z80: removed dead symbol import
Alan Cox [Tue, 7 Aug 2018 23:05:33 +0000 (00:05 +0100)]
kernel.def: add PAGE2 define
We'll need that shortly
Alan Cox [Tue, 7 Aug 2018 23:04:18 +0000 (00:04 +0100)]
font: add an expanded 8x8 font for 2bpp displays
We'll need this for the SAM Coupe where we don't have a 1pp high res mode.
(We may want a 6bit to 12bit font in the end but for now keep it simple).
Alan Cox [Thu, 2 Aug 2018 20:55:45 +0000 (21:55 +0100)]
tzset: more patches moving towards proper timezone support
It's enough to make you want summer time abolished!
Alan Cox [Tue, 31 Jul 2018 19:55:51 +0000 (20:55 +0100)]
trslabel: fix missing error argument
Alan Cox [Tue, 31 Jul 2018 19:55:29 +0000 (20:55 +0100)]
rc2014: add devinput
Tormod Volden [Sat, 28 Jul 2018 11:39:37 +0000 (13:39 +0200)]
Build setdate for all platforms and add it to filesystem
seq was also missing on 6502 and pdp11.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Sat, 28 Jul 2018 10:36:36 +0000 (12:36 +0200)]
dragon-nx32: Update README
Also remove XRoar patch which went upstream.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Alan Cox [Fri, 27 Jul 2018 21:00:08 +0000 (22:00 +0100)]
gm8x9: fix typo
Alan Cox [Fri, 27 Jul 2018 20:59:21 +0000 (21:59 +0100)]
dragon-nx-32: tweaks to scsi driver
No way to test this yet so I doubt it works but it'll not-works better than
before 8)
Alan Cox [Fri, 27 Jul 2018 20:56:27 +0000 (21:56 +0100)]
rc2014: do a pile of cleanup work
- Start working on tty autodetect
- Sort out non standard SIO layouts
Still need to look further into the CTC usage and tidy up the boot logic so
we can do a handy boot from CP/M
Alan Cox [Fri, 27 Jul 2018 20:52:33 +0000 (21:52 +0100)]
pcw8256: update README
Alan Cox [Fri, 27 Jul 2018 20:52:09 +0000 (21:52 +0100)]
rc-files: run setdate in the boot up
Tormod Volden [Tue, 24 Jul 2018 21:38:44 +0000 (23:38 +0200)]
dragon-nx32: (MOOH) Optimized fork copy bank routine
Around twice as fast. Now about 0.24 s for a 24KB large sh.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Alan Cox [Tue, 24 Jul 2018 23:16:40 +0000 (00:16 +0100)]
trs80m1: update README
Alan Cox [Tue, 24 Jul 2018 23:16:19 +0000 (00:16 +0100)]
pcw8256: correct clock rate
Alan Cox [Tue, 24 Jul 2018 23:15:38 +0000 (00:15 +0100)]
fsck: note an improvement to make
Alan Cox [Tue, 24 Jul 2018 23:15:25 +0000 (00:15 +0100)]
mkdir: fix size check
Tormod Volden [Mon, 23 Jul 2018 23:15:20 +0000 (01:15 +0200)]
init: Allow empty process field in inittab
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:57:38 +0000 (23:57 +0200)]
dragon-nx32: Add virtual consoles (6847 text mode)
Copy and rename the common CONFIG_VT_SIMPLE code and use it with the
6847 text mode.
This gives us:
tty1 Graphic mode console at 0x0400
tty2 CRT9128
tty3 VC 0 text mode at 0x1c00
tty4 VC 1 text mode at 0x1e00
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:57:37 +0000 (23:57 +0200)]
dragon-nx32: Reduce crt9128 screen size because of overscan
On most monitors the last columns and lines of the CRT9128 output
are not visible.
The sync parameters were mask programmable on the CRT9128 so there might
be exceptions but this seems a common issue with the standard parts
available.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:57:36 +0000 (23:57 +0200)]
dragon-nx32: Add dual-screen support with CRT9128
Adds CRT9128 card on tty2 with shared keyboard. Switch tty with
ctrl-1 and ctrl-2 (CLEAR-1 and CLEAR-2 on Dragon keyboard).
The 6847 graphics VT interface functions are made private and
these or the CRT9128 ones are called depending on the current TTY.
Add video.h just in case (not needed since multiplexer is asm).
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:57:35 +0000 (23:57 +0200)]
crt9128: Add timeout in sync wait
And try reset the chip if there is a timeout.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:57:34 +0000 (23:57 +0200)]
crt9128: Rename VT interface functions to be private
So that they can be used in multi-head setups.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:57:33 +0000 (23:57 +0200)]
dragon-nx32: Remove unused VT macros in config.h
Previously used with CONFIG_VT_SIMPLE
VT_BASE remains in use in devtty.c
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:48:32 +0000 (23:48 +0200)]
dragon-nx32: Make dwload support MOOH
It should remain compatible with the nx32 boards (Spinx-512).
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:48:31 +0000 (23:48 +0200)]
dragon-nx32: Allow building MOOH variant (nx32 memory model)
This MOOH variant just groups the 8KB pages into 32KB banks so that it
can run as an nx32 system.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Tormod Volden [Mon, 23 Jul 2018 21:40:28 +0000 (23:40 +0200)]
dragon-nx32: spi.s: Use macro defines for 65SPI flags
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Alan Cox [Tue, 24 Jul 2018 23:12:57 +0000 (00:12 +0100)]
Makefile.pdp11: add Makefile that was omitted
Alan Cox [Tue, 24 Jul 2018 23:12:39 +0000 (00:12 +0100)]
mkdir: documentation
Alan Cox [Sun, 22 Jul 2018 22:26:54 +0000 (23:26 +0100)]
pcw8256: fix defines for networking
Alan Cox [Sun, 22 Jul 2018 22:25:46 +0000 (23:25 +0100)]
font8x8; revert deconstification
We don't want sdcc making a huge initializer blob of it. Once we fix sdcc
we can sort this out. It might matter for other ports if so we may have to
ifdef it a bit
Alan Cox [Sun, 22 Jul 2018 15:55:17 +0000 (16:55 +0100)]
tzset: add draft support for shift time not just day
Alan Cox [Sun, 22 Jul 2018 14:16:38 +0000 (15:16 +0100)]
sys/super.h: properly expose the structure in user space form
Alan Cox [Sun, 22 Jul 2018 14:16:25 +0000 (15:16 +0100)]
tzset: continue working on daylight savings
Alan Cox [Sun, 22 Jul 2018 12:54:48 +0000 (13:54 +0100)]
tzset: first cut at a fullish parser
Alan Cox [Sat, 21 Jul 2018 23:37:44 +0000 (00:37 +0100)]
tzset: parse more format information
This now supports the most basic format.
Alan Cox [Sat, 21 Jul 2018 23:35:57 +0000 (00:35 +0100)]
libs: for now at least put a valid byte in isdst
Alan Cox [Sat, 21 Jul 2018 23:35:11 +0000 (00:35 +0100)]
date: rewrite and add manual page
We still need to support custom formats but that needs the fancy time format
stuff we don't yet have.
Alan Cox [Sat, 21 Jul 2018 20:55:14 +0000 (21:55 +0100)]
libc: add basical localtime support
We now pass the right things around to make this work.
At the moment the only format understood is zone+-shift in hours. So for example
TZ=BST+1.
Alan Cox [Sat, 21 Jul 2018 19:41:45 +0000 (20:41 +0100)]
localtim_r: do time zone changes
We had local/gmtime swapped
Alan Cox [Sat, 21 Jul 2018 19:41:06 +0000 (20:41 +0100)]
gmtime_r: is not localtime_r .. oops